InstrumentsPressure and temperature measurementT +49 40 5247 4156 · M +49 176 3130 5711sales@eurekaeu.com
Engine control room console with dial indicators, alarm panels and monitors

Home / Applications / Marine and offshore

Industry · Marine and offshore

Instruments for engine rooms, pump rooms and offshore units

Pressure gauges, pressure transmitters, thermometers and temperature sensors for two- and four-stroke main and auxiliary engines, pumps, tanks and filters. Specified to your range, connection and approval requirements – and quoted by us.

  • Gauges from −1 to 1600 bar
  • Liquid-filled, vibration-proof dials
  • AISI 316 wetted parts available
  • DNV type approval for selected gauge series
−1 … 1600 barpressure gauge measuring ranges
DN 63 – 160dial sizes for local reading
−80 … +500 °Cdial thermometer range
0.5 – 50 mcapillary for remote-reading thermometers

Requirements

What marine service asks of an instrument

Engine rooms mean vibration, shock and harsh maritime conditions. These are the points we check with you before we quote – all values from the manufacturer’s datasheets.

01

Measuring points and media

  • Two- and four-stroke main and auxiliary engines, pumps, tanks and filters
  • Exhaust gas temperature on main and auxiliary engines
  • Diaphragm gauges with kPa/mbar scales for low pressures, for example on LNG tanks
02

Ranges and accuracy

  • Pressure gauges from −1 bar up to 1600 bar, minimum span 1 bar
  • Accuracy class 1.0; class 1.6 on DN 63
  • Units bar, kPa, MPa, psi, mH₂O and more – dual scales possible
  • Dial thermometers −80 to +500 °C, class 1 to EN 13190
03

Vibration and liquid filling

  • Vibration-proof gauge series, dry or filled with glycerine or silicone
  • Stainless gauge: glycerine above 2 bar, silicone below 2 bar, dry on request
  • Transmitters built for mechanical stress, vibration and shock in harsh maritime environments
  • Rigid-stem thermometers designed to withstand strong vibrations
04

Wetted materials

  • Measuring systems and connections in brass/bronze, steel or AISI 316
  • All-AISI 316 version: case, front ring, connection and measuring system
  • Thermometer sensor tubes and capillary armour in AISI 316
  • Pressure transmitters in all-stainless construction
05

Connections and mounting

  • Bottom or rear connection; direct, surface or panel mounting
  • More than 40 connection threads in three materials, e.g. G½B brass
  • Remote-reading thermometers: surface, panel or bracket mounting
  • Rigid-stem thermometers with IP 68 enclosure (10 mH₂O)
06

Hazardous areas and safety

  • Safety-pattern gauges with a blow-out back to EN 837-1, clause 9.7.2, for LNG, chemical, offshore and oil & gas service
  • Other explosion-protection requirements are confirmed per enquiry
✓

Class approval

Specified pressure gauge (manometer) series hold DNV type approval under the DNV rules for classification of ships, offshore units and high-speed and light craft. The approval covers only the listed pressure gauge types.

Tell us the classification society your vessel or unit needs. We confirm per model what applies and send the relevant certificate with our quotation on request.

In service

Where marine instruments work

Four-stroke marine diesel engine with a local gauge board for oil, water and air pressures
Main engine with local gauge board
Engine gauge board with lube oil, fuel oil, HT and LT water, charge air and starting air gauges
Engine gauge board
Engine control room console with rows of dial indicators
Control console with dial indicators
Engine room of a modern ferry with pumps, pipework and local pressure gauges
Engine room with pumps and local gauges

Photos show typical installations. Image credits.

Typical applications

How instruments are typically used on board

Two common scenarios. They describe typical installations, not a specific vessel or customer.

Engine gauge board with HT and LT cooling-water gauges
Scenario 1

Main-engine cooling-water pressure monitoring

Cooling-water pressure at the engine inlet is one of the readings an engineer checks on every round – and one the alarm system watches around the clock.

  1. A liquid-filled pressure gauge at the pump outlet and engine inlet gives a steady local reading, even with engine vibration.
  2. A pressure transmitter on the same line sends the value to the alarm and monitoring system.
  3. A pressure switch or a gauge with contacts can trigger the low-pressure alarm at a set point.

What we need from you: range and unit, connection thread, filling, output signal and the class approval required.

Marine diesel engine in the engine room
Scenario 2

Exhaust-gas temperature on main and auxiliary engines

Exhaust-gas temperature is one of the key readings on a diesel engine – the crew wants it on a dial at the engine and in the monitoring system at the same time.

  1. A mechatronic thermometer combines the dial thermometer with a type K thermocouple in one stem – both measure at the same point.
  2. The engineer reads the dial on site; the thermocouple feeds the monitoring system through a single terminal socket.
  3. Sensor and thermometer can be exchanged independently. Ranges 0–500, 0–600 and 50–650 °C.

What we need from you: range, immersion length, connection and the signal your monitoring system expects.

Engineering

Technical notes and common faults

General engineering points we check with you. They are not a guarantee for a specific installation.

Pointer flutter

Engine vibration and pulsation shake the pointer and wear the movement. A liquid-filled gauge or a damping element steadies the reading.

Gauge damaged by pressure peaks

Pump starts and water hammer can exceed the scale. State peaks and overpressure separately from the working range.

Wrong reading at the monitoring system

Signal type, supply and connector must match the alarm system. Tell us the system and the signal it expects.

Documents

Datasheet with the quotation. Calibration documents and, where available for the product type, certificates are confirmed per model. Resources and checklists →

Why FEX

What you get with us

Calibrated one by one

Each pressure gauge is calibrated manually and individually at five points on the scale, upwards and downwards. Bourdon tubes are heat-treated to reduce hysteresis.

Built to your specification

Standard products and customer-specified versions come from one modular system – ranges, threads, fills and mounting to suit the measuring point.

Documents with the order

Datasheet with the quotation. Calibration documents and, where available for the product type, certificates are prepared to match your order.

One contact in Hamburg

Selection, quotation, documentation, shipping to your site or vessel and after-sales – coordinated from Hamburg.

Send us your marine specification

  1. Medium and temperature
  2. Range and unit
  3. Connection and mounting
  4. Output: dial, signal or contacts
  5. Class approval required
  6. Quantity and delivery port

Ready to specify an instrument?

Send us the measuring point and requirements – we reply with a written quotation and the matching datasheet.

FEX Global · Am Kaiserkai 13, 20457 Hamburg · T +49 40 5247 4156 · M +49 176 3130 5711 · sales@eurekaeu.com